全自動封膠線實操科普：板壓壓合效果差？四角落差這樣調精準

　　Practical popularization of fully automatic sealing line: Poor board pressing effect? Adjust the four corner drop accurately like this

　　在全自動封膠線的生產流程中，板壓環節是保障中空玻璃合片后貼合緊密的核心工序。板壓壓合效果直接影響后續封膠質量——如果壓合不勻，會導致玻璃間存在縫隙，后續容易出現密封不嚴、起霧進水等問題；要是四角壓力偏差大，還可能造成玻璃受力不均、邊緣破損。不少一線操作人員遇到板壓壓合效果不好時，不知道從何下手，其實核心解決方案就是調整四角落差，讓板壓面保持水平。今天就結合實操細節，給大家科普全自動封膠線板壓四角落差的調整方法。

　　In the production process of the fully automatic sealing line, the plate pressing step is the core process to ensure a tight fit of the insulated glass after lamination. The pressing effect of the board directly affects the subsequent sealing quality - if the pressing is not uniform, it will cause gaps between the glass, which can lead to problems such as poor sealing, fogging, and water ingress in the future; If there is a large deviation in the four corner pressure, it may also cause uneven stress on the glass and edge damage. Many frontline operators do not know where to start when the board pressing effect is not good. In fact, the core solution is to adjust the four corner drop to keep the board pressing surface level. Today, based on practical details, we will explain to you the adjustment method of the four corner drop of the fully automatic sealing line board.

　　先跟大家理清核心邏輯：板壓能實現均勻壓合，關鍵在于四個角的距離一致，形成平整的壓合面。一旦某一角距離偏差過大，就會出現局部壓合不實或過度擠壓的情況。調整的核心思路很簡單：先通過測量找到誤差大的角，再通過調節部件修正距離，最后固定鎖死，全程圍繞“找平四角落差”展開，不用復雜設備，普通測量工具和扳手就能完成。

　　First, let me clarify the core logic: board pressing can achieve uniform pressing, and the key is that the distance between the four corners is consistent, forming a flat pressing surface. Once the distance deviation of a certain corner is too large, there will be local compression or excessive squeezing. The core idea of adjustment is simple: first, find the angle with large error through measurement, then correct the distance through adjusting the components, and finally fix and lock it. The whole process revolves around "leveling the four angle drop", which can be completed without complex equipment, ordinary measuring tools and wrenches.

　　第一步，張開板壓，精準測量四角落差。首先操作設備，將板壓張開到合適的操作位置，確保有足夠的空間測量和調整。然后拿出鋼板尺或卷尺，以板壓的基準面為參照，分別測量四個角的間距數值，做好清晰記錄。比如測量后發現，三個角間距都是350mm，唯獨一個角是352mm，這就明確了調整目標——重點修正這個誤差2mm的角，讓其間距與其他三角保持一致。

　　The first step is to open the plate and accurately measure the four corner drop. Firstly, operate the equipment and spread the board to the appropriate operating position to ensure sufficient space for measurement and adjustment. Then take out a steel ruler or tape measure, use the reference surface of the plate as a reference, measure the spacing values of the four corners separately, and make clear records. For example, after measurement, it was found that the spacing between the three corners was 350mm, but only one corner was 352mm. This clarifies the adjustment goal - to focus on correcting this angle with an error of 2mm, so that its spacing is consistent with other triangles.

　　第二步，拆解固定螺絲，調節目標角滾珠絲杠。找到誤差較大的角對應的調節部件，先將該角的四顆固定螺絲用扳手依次拆下，注意把螺絲妥善收納，避免丟失或混淆。拆完螺絲后，找到對應的滾珠絲杠（也就是大家常說的“滾螺絲杠”），這是調節板壓間距的核心部件。這里要記住關鍵調節規律：順時針擰動滾珠絲杠，板壓會逐漸壓緊，對應間距變??；逆時針擰動，板壓會松開，對應間距變大。

　　Step two, disassemble the fixing screws and adjust the target angle ball screw. Find the adjustment component corresponding to the angle with a large error, and first remove the four fixed screws of the angle one by one with a wrench. Pay attention to properly storing the screws to avoid loss or confusion. After removing the screws, find the corresponding ball screw (also known as the "rolling screw rod"), which is the core component for adjusting the plate pressure spacing. Remember the key adjustment rule here: turn the ball screw clockwise, and the plate pressure will gradually tighten, corresponding to a smaller spacing; Turning counterclockwise will release the plate pressure and increase the corresponding spacing.

　　調節時要小幅度轉動絲杠，每擰動半圈就用尺子復測一次間距，避免一次調幅過大導致誤差反向。比如之前誤差2mm的角，需要順時針擰動絲杠，逐步將間距從352mm調整到350mm，與其他三角保持一致。調整過程中要耐心，確保間距數值精準，這是保證壓合均勻的關鍵。

　　When adjusting, the screw should be rotated slightly, and the spacing should be re measured with a ruler every half turn to avoid errors caused by excessive amplitude adjustment. For example, for an angle with a previous error of 2mm, the screw needs to be turned clockwise to gradually adjust the spacing from 352mm to 350mm, keeping it consistent with other triangles. Patience is required during the adjustment process to ensure accurate spacing values, which is the key to ensuring even compression.

　　第三步，復核間距，擰緊固定螺絲。當目標角間距調整到位后，再次用尺子復測四個角的間距，確認所有數值一致、無偏差。復核無誤后，將之前拆下的四顆固定螺絲重新裝回原位，用扳手依次擰緊。擰緊時要注意力度均勻，避免過度用力損壞螺紋，同時確保螺絲完全鎖死，防止設備運行中因振動導致板壓位置偏移，再次出現壓合問題。

　　Step three, review the spacing and tighten the fixing screws. After adjusting the target angle spacing in place, use a ruler to re measure the spacing between the four corners and confirm that all values are consistent and have no deviation. After verifying that there are no errors, reinstall the four previously removed fixing screws and tighten them in sequence with a wrench. When tightening, pay attention to even force to avoid damaging the threads with excessive force. At the same time, ensure that the screws are completely locked to prevent the displacement of the plate pressing position due to vibration during equipment operation, which may cause pressing problems again.

　　這里補充幾個實操注意點：一是調整前必須讓設備停機并鎖定，避免板壓意外動作造成安全隱患；二是測量時要保證尺子放正，讀數精準，避免因測量誤差導致調整失效；三是如果多個角存在誤差，要逐一調整，調整完一個角就復核一次整體間距，防止相互影響；四是調整完成后，建議空載運行一次板壓動作，觀察是否平穩，再進行試生產。

　　Here are a few practical points to note: firstly, the equipment must be shut down and locked before adjustment to avoid safety hazards caused by unexpected board pressure movements; The second is to ensure that the ruler is placed correctly and the reading is accurate during measurement, in order to avoid adjustment failure caused by measurement errors; Thirdly, if there are errors in multiple corners, they should be adjusted one by one. After adjusting one corner, the overall spacing should be rechecked to prevent mutual influence; Fourthly, after the adjustment is completed, it is recommended to run the plate pressing action without load once, observe whether it is stable, and then proceed with trial production.

　　日常維護也能提前預防板壓壓合問題：建議每月定期測量一次板壓四角落差，發現輕微偏差及時調整，避免小問題積累成大故障；同時定期檢查固定螺絲的緊固狀態，防止振動導致松動；還要保持滾珠絲杠的清潔，定期涂抹潤滑油，確保調節順暢，減少部件磨損。

　　Daily maintenance can also prevent board pressing problems in advance: it is recommended to regularly measure the four corner drop of the board pressing once a month, and adjust any slight deviations in a timely manner to avoid small problems accumulating into major failures; Regularly check the fastening status of the fixing screws to prevent loosening caused by vibration; It is also necessary to keep the ball screw clean and regularly apply lubricating oil to ensure smooth adjustment and reduce component wear.

　　板壓調整是全自動封膠線的基礎維護技巧，看似簡單，卻直接決定封膠質量和產品合格率。對一線操作人員來說，掌握“測量-調節-固定”的核心步驟，就能快速解決壓合效果不佳的問題，減少返工和生產延誤。希望這次科普能幫到大家，要是調整后仍有壓合問題，可進一步檢查板壓面是否有異物、部件是否磨損，或聯系設備廠家技術支持。

　　Plate pressure adjustment is a fundamental maintenance technique for fully automatic sealing lines. Although it may seem simple, it directly determines the sealing quality and product qualification rate. For frontline operators, mastering the core steps of "measurement adjustment fixation" can quickly solve the problem of poor pressing effect, reduce rework and production delays. I hope this science popularization can help everyone. If there are still pressing problems after adjustment, you can further check whether there are foreign objects on the pressing surface of the board, whether the components are worn, or contact the technical support of the equipment manufacturer.

　　本文由  全自動封膠線 友情奉獻.更多有關的知識請點擊  http://m.ruiyingjituan.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the fully automatic sealing line For more related knowledge, please click http://m.ruiyingjituan.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.